Force Measurement Test Frames FOR USE WITH L3, L2 PLUS, L2 AND S2 SOFTWARE Specifica tions FMx Force Measurement Frames Model No. FMS-500 FMS-1000 FMS-2500 FMS-5000 FMD-10K FMD-30K FMD-50K Load Capacity N 500 1000 2500 5000 10,000 30,000 50,000 kgf 50 100 250 500 1000 3000 5000 lbf 112 225 562 1124 2250 6750 11,250 Minimum Speed mm/min 0.05 0.05 0.05 0.05 0.001 0.001 0.001 in/min 0.002 0.002 0.002 0.002 0.00004 0.00004 0.00004 Maximum Speed mm/min 1525 1525 1525 1525 1525 1525 752 in/min 60 60 60 60 60 60 30 Position Control Resolution µm 0.250 0.250 0.250 0.250 0.05 0.025 0.025 µin 9.8 9.8 9.8 9.8 1.9 0.9 0.9 Vertical Test Space1 mm 559 953 1257 1257 1270 1245 1220 in 22 37.5 49.5 49.5 50 49 48 Total Crosshead Travel mm 381 762 1016 1016 1162 1137 1111 in 15 30 40 40 45.75 44.75 43.75 Throat mm 100 100 100 100 424 424 424 in 4 4 4 4 16.7 16.7 16.7 Accuracy Load Measurement Load Cell Sensor Dependent Load Cell Sensor Dependent Accuracy Position Measurement2 ±0.001inch (±20µm) ±0.0002inch (±5µm) Accuracy Crosshead Speed ±0.1% of set speed ±0.1% of set speed Data Sampling Hz 5 to 1000 5 to 1000 Digital I/O 8 channels @ 1-5V 8 channels @ 1-5V Electrical Phase 1 1 Power Requirements 100,120,220,230,240VAC 10%; 47-63Hz Self-identifying 100, 120, 220, 230, 240Vac 10% Single Phase Voltage (Vac) ±10% 220-240V Single Phase Voltage (Vac) ±10% 220-240V Operating Temperature °C +10° to +38°C +10° to +38°C °F +50° to 100°F +50° to 100°F StorageTemperature °C -40° to +66°C -40° to +66°C °F -40° to 150°F -40° to 150°F Humidity +10% to +90%, non-condensing +10% to +90%, non-condensing Total Height mm 805 1218 1573 1573 1685 1711 1711 in 31.7 47.9 61.9 61.9 66.4 67.4 67.4 Total Width mm 381 381 381 381 787 787 787 in 15 15 15 15 31 31 31 Total Depth mm 514 514 514 514 724 724 724 in 20.3 20.3 20.3 20.3 28.5 28.5 28.5 Weight kg 61 77 88 88 136 192 225 lb 135 170 195 195 300 425 500 Notes Total vertical space is the distance from the top surface of the base plate to the bottom surface of the crosshead, excluding load cell sensor, test fixtures, and clevis adapter. Assumes Linear Error Correction and Deflection Compensation has been performed on test frame. Shown: L2 system with FMS500 test frame with tablet. 509 starrett.com M a terial T esting / F orce M easurement